[1]刘涛,宋涛,曹清松.轧辊偏心的间歇采样重复控制补偿[J].燕山大学学报,2017,41(3):219-222.[doi:10.3969/j.issn.1007-791X.2017.03.003]
 LIU Tao,SONG Tao,CAO Qingsong.Intermittent sampling repetitive control for roll eccentricity compensation[J].Journal of YanShan University,2017,41(3):219-222.[doi:10.3969/j.issn.1007-791X.2017.03.003]
点击复制

轧辊偏心的间歇采样重复控制补偿
分享到:

《燕山大学学报》[ISSN:1007-791X/CN:13-1219/N]

卷:
41
期数:
2017年第3期
页码:
219-222
栏目:
机械工程
出版日期:
2017-05-31

文章信息/Info

Title:
Intermittent sampling repetitive control for roll eccentricity compensation
文章编号:
1007-791X(2017)03-0219-04
作者:
刘涛12*宋涛12曹清松12
1. 燕山大学 河北省重型机械流体动力传输与控制重点实验室,河北 秦皇岛 066004;2.先进锻压成形技术与科学教育部重点实验室(燕山大学),河北 秦皇岛 066004
Author(s):
 LIU Tao12SONG Tao12CAO Qingsong12
1.Hebei Provincial Key Laboratory of Heavy Machinery Fluid Power Transmission and Control,Yanshan University,Qinhuangdao,Hebei 066004,China;2.Key Laboratory of Advanced Forging & Stamping Technology and Science (Yanshan University),Ministry of Education of China,Qinhuangdao,Hebei 066004,China
关键词:
轧辊偏心 采样控制 重复控制板厚控制
Keywords:
roll eccentricityintermittent samplingrepetitive controlAGC
分类号:
TG333.7
DOI:
10.3969/j.issn.1007-791X.2017.03.003
文献标志码:
A
摘要:
针对轧辊偏心信号时域频率高且频率存在变化,常规方法难以有效补偿的问题,提出了一种新的重复控制补偿方法。首先依据阶比分析原理,把板厚反馈信号转换为角域信号,使包含在板厚反馈信号中的偏心扰动具有严格的周期性。然后针对板带轧制及轧辊偏心特点,并通过采样控制克服板厚信号大滞后问题。将该系统嵌入到AGC(自动板厚控制)系统之中,以消除轧辊偏心对出口板厚的影响。在SIMULINK环境下的仿真表明,该方法可以在支撑辊转动50转内将轧辊偏心造成的厚差波动降低80%。
Abstract:
In the light of the difficulty of roll eccentricity compensation caused by its high and unstable frequency,a new intermittent sampling repetitive control compensation method is provided.Firstly,the plate thickness feedback signal is converted into angle domain signal based on order analysis principle,to make the eccentric disturbance in the feedback thickness signal has a strict periodicity.Secondly,according to the characteristic of strip rolling and roll eccentricity,the special repetitive controller is designed,and an intermittent adjustment sampling controller is used to overcome the problem of thickness signal delay.This system is embedded into the AGC system to eliminate the influence of roll eccentricity on the exit thickness.By modeling and simulation in the MATLAB/SIMULINK ,it is showed that the repetitive controller can decrease the 80% of variation of thickness deviation caused by roll eccentricity after 50 rotations of supporting roller.

相似文献/References:

[1]杨 阳,王益群,等.轧辊偏心自动分层确定阈值滤波法[J].燕山大学学报,2013,(5):430.[doi:10.3969/j.issn.1007-791X.2013.05.010]
 YANG Yang,WANG Yi-qun,CHEN Gang.Roll eccentricity filtering method of automatically decision of decomposition level and threshold value[J].Journal of YanShan University,2013,(3):430.[doi:10.3969/j.issn.1007-791X.2013.05.010]

备注/Memo

备注/Memo:
收稿日期:2016-08-17        责任编辑:王建青
基金项目:河北省自然科学基金钢铁联合研究基金资助项目(E2013203126);国家自然科学基金资助项目(51305389)
作者简介:*刘涛(1973-),男,河北昌黎人,博士,副教授,主要研究方向为自动化控制及机电液综合控制系统,Email:liutao@ysu.edu.cn
更新日期/Last Update: 2017-07-07